If your washing machine is shaking violently, stop the cycle if it is walking across the floor or hitting anything, and let the drum stop before you open the door or lid. If the washer is new or was recently moved, check your manual for shipping hardware before you run it again. Redistribute the laundry and remove some items if the tub is packed. Then rock the washer gently while it is off and adjust the feet if a corner moves. Finish with the test cycle recommended for your model. If it still shakes violently after these checks, stop using it and book service.
| What you notice | Check first |
|---|---|
| It started with this load | Pause, spread the laundry, take some items out |
| The washer is new or was just moved | The model-specific shipping hardware |
| A corner moves when you push on it | The feet and lock nuts, then the floor |
| It shakes only at high spin | Load balance and spin speed |
| It still shakes violently on a test cycle | Book service |
Table of Contents
Is Your Washing Machine Shaking Violently or Just Vibrating?
Some shaking during the spin cycle is normal, because the drum turns fastest then and any imbalance shows. Samsung adds that a washer can vibrate at the start of a cycle while it senses the load.
It is too much if the washer walks or jumps across the floor, thumps, bangs or vibrates loudly. Maytag says a washer should not walk across the floor or make those sounds, and Whirlpool says walking or jumping across the floor is not normal. If yours does, use the checks below.
If the washer stays in place and the main problem is the noise, use our Washing Machine Making Loud Noise guide instead.
Did It Start With This Load?
Pause the cycle and wait until the drum stops before you open the door or lid. Then:
- Spread the laundry evenly around the drum. A single heavy item such as a comforter or rug can throw it off balance, so add a few items to help balance the load.
- Take items out if the clothes can’t move freely. Whirlpool says not to pack the drum tightly.
- If it was a very small load, add a few items or lower the spin speed. Samsung says small loads can bunch up on one side.
Restart the cycle. If it runs calmly, that points to the load. If it shakes again, go on.
Is the Washer New or Recently Moved?
Many front-loaders use shipping bolts at the back to hold the tub during transport. If they stay in, the washer shakes hard, and LG warns that it can permanently damage the washer. Don’t run another cycle until you have checked.
Open the door and push the drum. It should feel springy, with some give. If the drum feels unusually rigid, recheck the shipping hardware against your model’s installation instructions before running the washer.
Follow your model’s installation instructions to remove the shipping hardware, and keep it for your next move. Unplug the washer first if the floor is dry, and don’t tip the washer to reach the bolts. If you can’t reach them or can’t get them out, book service.
Top-loaders are different. Samsung says its top-loaders have no shipping bolts, but some GE top-loaders ship with a shipping rod. Check your manual for any shipping material.
Does the Washer Rock When It Is Off?
Push down on each top corner, then push the washer side to side and front to back. It should sit firmly on all four feet.

If a corner moves:
- Adjust that foot. On a front-load, loosen the lock nut, turn the foot, then tighten the nut firmly against the washer base so the foot can’t drift.
- Keep the feet as short as you can. Longer feet make the washer shakier.
- Set a level on top, side to side and front to back, and rock the washer again. The bubble should sit centered and all four feet should touch the floor.
Then look at the floor. The washer needs a solid, level floor. LG says a raised or uneven base causes vibration, and Whirlpool says to check for a floor that flexes or sags and not to put a front-loader on a raised wooden platform. Carpet adds some vibration, according to Samsung. If the floor flexes, LG’s advice is to move the washer or have the floor reinforced.
If the washer sits on a pedestal, check that the pedestal is firmly mounted and level, and empty its drawer of anything loose that could rattle.
Run One Test Cycle
When the load, the shipping hardware and the feet are checked, run a test cycle, such as a rinse and spin, and follow your model’s instructions. GE recommends a rinse and spin with no load on its front-loaders, and says that if the vibration is normal, the wash load caused the imbalance. Samsung suggests a small test load, and LG uses a rinse-and-spin or spin-only cycle.
- Calm: that points to the load. Wash smaller, balanced loads, and lower the spin speed for bulky items.
- Still violent: stop the test and book service.
If it starts walking or banging during the test, stop the cycle.
Brand Notes
| Brand | What changes the fix |
|---|---|
| Samsung | If your manual lists calibration mode (Cb), run it with the drum empty after you level the washer. Some vibration is expected on a pedestal, even when the washer is level. |
| LG | If shaking starts mid-wash, pause, redistribute the load and restart. If your LG washer shows UE, uE or Ub, see our LG Washer UE Code guide for checks specific to your washer type. For front-load models, LG recommends keeping the drum about two-thirds full. |
| GE | On a front-load, an occasional movement of up to 1/4 inch is normal. GE also notes that a clogged drain pump can cause vibration. If water is slow to drain or stays in the drum, use our Clothes Washer Won’t Drain guide. |
When to Stop and Book Service
Book service if any of these apply:
- It still shakes violently on a test cycle after the checks above.
- The shipping bolts won’t come out, or you can’t reach them.
- With the washer off, the drum looks off-center, or you hear grinding or clanking when you move it by hand.
- The washer keeps walking after you level it and the floor is solid.
Don’t open the cabinet to look for the cause. If the washer still shakes violently after the external checks, the problem may be inside the suspension or drum system and needs a technician. Tell the technician your model number, whether it still shakes on a test cycle, and which checks you have done.
For other washer problems, continue with our Washing Machine Troubleshooting guide.
Sources
- Samsung US: Samsung washing machine is shaking too much
- LG USA: Troubleshooting vibration issues on an LG washing machine
- LG USA: Troubleshooting vibration issues
- LG USA: Front-load washer vibrations and the floor
- LG USA: Front-load washer UE/Ub error code
- Whirlpool: How to stop a washer from shaking
- Whirlpool Product Help: Vibration, walking or off balance, front-load washer
- Maytag: How to stop a washing machine from shaking
- GE Appliances: Front load washer, walking, vibrating, shaking or moving
- GE Appliances: Top load washer, walking or vibrating
Last reviewed: October 23, 2026