If your washing machine stops mid cycle, don’t reset it yet. Note any error code, check whether the display is still on, and see whether water is left in the drum. If the display went dark, first check whether the cycle had been paused, then check the power. If water is still in the drum after the washer should have drained, start with the drain path. A code or a stop that repeats at the same point gives you another clue. If it keeps stopping after the matching checks below, book service.
| What you see | Check first |
|---|---|
| The display is dark | Whether the cycle was paused, then the outlet and breaker |
| The display is on and water is still in the drum | The drain hose, then our Clothes Washer Won’t Drain guide |
| It stopped while filling | Both faucets and the hoses, then our Washing Machine Not Filling With Water guide |
| It shook hard, then stopped | The load, then our Washing Machine Shaking Violently guide |
| A code is showing | The code section below, or your manual |
| It pauses, then carries on | Watch it first. Some model-specific pauses are normal. |
| It stops at the same point every time | Note the stage and any code. Book service if it repeats after the matching checks. |
Table of Contents
Did the Washer Stop, or Is It Just Pausing?
Some pauses are the washer doing its job. Check for these before you reset anything:
- Suds. On Whirlpool and Maytag front-loaders,
SudorSdmeans too many suds. The washer extends the rinse, pausing the tumbling and adding water, and may repeat that several times. Use HE detergent. If you use “no splash” or “easy pour” liquid chlorine bleach, switch to regular liquid bleach, because it can make extra suds. Also check that the drain hose isn’t kinked or clogged. - A paused or cancelled cycle. On Whirlpool and Maytag front-loaders,
Intmeans the cycle was paused or cancelled. The washer may take 20 to 30 minutes to stop spinning and drain, and shows the code during that time. - A timer that holds still. On Whirlpool and Maytag front-loaders, a time that holds near the end of the cycle means the washer needs extra time to balance the load, often with a single bulky item such as a rug or bedding. Sanitize and Steam cycles heat the water first, which can also hold the time for a long stretch. Whirlpool gives no set wait time.
- Some GE washers. GE says that on washers with a timer, the timer can sometimes reach the pump-out part of the cycle while water is still in the tub. The washer tries to spin, senses the water, stops to pump out, and tries again. GE calls this normal and harmless. On certain GE top-loaders (electronic controls with a selector knob, made after August 2017), the washer runs cold water in two short bursts with a 10-second pause when a cycle starts or restarts. If the lid opens during that start-up, it pauses until you press Start.
The Display Went Dark
If water is on the floor near the plug or outlet, don’t reach for the plug. Switch off the breaker first.
Then check whether the cycle was paused. LG says that if a paused cycle isn’t resumed within about 4 minutes, the washer turns itself off. Restart the cycle.
LG USA Support has a video on this problem for its front-load washers:
If that isn’t it, check the power:
- Plug a lamp or another device into the outlet to test it.
- Switch the breaker fully off and back on. Samsung says a tripped breaker often looks like it’s on.
- Plug the washer straight into the wall. Samsung doesn’t recommend surge protectors with its washers.
- Look at the power cord. If it is damaged, don’t use the washer. Book service.
If the breaker trips again, stop using the washer.
If the washer stays completely dark and will not power back on, use our Washing Machine Won’t Turn On? Check the Control Panel First guide.
Washing Machine Stops Mid Cycle With Water in the Drum
Water left in the drum when the cycle should be moving on points to the drain path first. Look at the drain hose for kinks. Our Clothes Washer Won’t Drain guide covers the rest of the drain checks in order.
The Display Is On but the Cycle Won’t Move On
- Door or lid. Make sure nothing blocks the door and that it closes completely. Samsung says to open and close the door firmly, without slamming it, then press Start/Pause to restart.
- Load. If it stopped at the spin, check the load. LG says that if more weight settles on one side, the washer may stop spinning to prevent damage. Pause, spread the laundry evenly and resume. LG’s Spin Only cycle (press Spin Speed and choose a high setting) shows whether the drum spins. If it shook hard first, use our Washing Machine Shaking Violently guide.
- Wash action. If the washer keeps running but the laundry does not move during the wash portion, use our Washing Machine Not Agitating guide.
- Filling. If it stopped while filling, open both faucets fully and straighten the hoses, then use our Washing Machine Not Filling With Water guide.
A Code Is Showing
Codes differ between brands, so use your manual’s list. Samsung says to deal with a code before restarting the cycle. On Whirlpool and Maytag front-loaders, four codes relate to a stop:
| Code | What it means | Check |
|---|---|---|
F5 E2 | The door isn’t locking | Nothing blocking the door, and the door closes completely |
F7 E1 | The motor can’t reach the right speed | Shipping bolts removed, washer not overloaded |
F8 E1 | Low water flow | Faucets fully open and hoses not kinked |
F9 E1 | Draining takes longer than expected, typically over 8 minutes | Drain hose, and too many suds |
If You Need to Restart or Reset It
The right method depends on your brand and on what the washer is showing, so there is no single reset that fits all of them.
- Samsung (stops unexpectedly): deal with any code first. Then open and close the door firmly, choose the cycle again and press Start/Pause. These steps don’t include unplugging.
- Whirlpool and Maytag front-loaders: for
Int,F5 E2,F7 E1andF8 E1, press Pause or Cancel twice and Power once. IfIntis still showing, or for other F and E codes, unplug the washer for 5 minutes, plug it back in, choose the cycle again and press Start. ForSud,SdandF9 E1, follow the cause-specific checks above instead of forcing a reset. - LG (washer powered off mid-cycle): unplug the washer and turn off the breaker. Hold START/PAUSE for 5 full seconds, plug it back in, turn the breaker on and power the washer on.
- GE: turn off the breaker or unplug the washer for 2 minutes. On electronic models, restore power, then choose and start the cycle again.
Unplug the washer only if the floor is dry. If there is water near the plug, use the breaker.
When to Stop and Book Service
Book service if any of these apply:
- It stops at the same point every time after the checks above.
- A code returns after your brand’s restart steps.
- The washer has no power after the outlet and breaker checks, or the cord is damaged.
- The breaker trips again after you reset it.
Don’t open the cabinet or test electrical parts. If it keeps stopping after the outside checks, the cause is inside the washer and needs a technician. Tell the technician your model number, the code, and the stage where it stops.
For other washer problems, continue with our Washing Machine Troubleshooting guide.
Sources
- Whirlpool Product Help: Error codes in front-load washers
- Whirlpool Product Help: Cycle time is not advancing, front-load washer
- Maytag Product Help: Error codes in front-load washers
- Maytag Product Help: Cycle time is not advancing, front-load washer
- Samsung US: Power issues with Samsung washing machine
- LG USA: Washer powered off mid-cycle
- LG USA: Drum does not spin, or starts and stops
- GE Appliances: Washer, spins and stops repeatedly
- GE Appliances: Top load washer, start-up and automatic draining sequences
- GE Appliances: Washer, resetting the electronic controls
Last reviewed: October 14, 2026