If your washing machine won’t turn on, look at the control panel first. No lights at all? Check the outlet and breaker before you assume the washer has failed. Lights on but the cycle won’t start? Check the door or lid, the control lock and any delay setting, and note any code. If it starts but shuts off during the cycle, that is a different problem. If these checks don’t help, book service.
| What you see | Check first |
|---|---|
| No lights or display | The outlet, breaker and GFCI, then the plug and cord |
| Lights on, but Start does nothing | The door or lid, then the control lock |
A lock icon, LoC, LC or CL | Unlock the controls |
dr or Lid | Open and close the door or lid, then start again |
A delay time, such as 3h | Whether a delay option is active |
| Starts, then shuts off | Our Washing Machine Stops Mid Cycle guide |
Table of Contents
Washing Machine Won’t Turn On: No Power or Lights
If there is water on the floor near the plug or outlet, don’t reach for the plug. Switch off the breaker first.
Then work through the power in this order:
- Plug the washer straight into a grounded wall outlet. Whirlpool, Maytag and LG advise against extension cords, and Samsung and LG advise against surge protectors.
- Test the outlet with a lamp or another device. If that device doesn’t work either, the washer isn’t the problem.
- If the outlet has a GFCI, press its reset button. LG, Whirlpool and Maytag all list this.
- Switch the breaker fully off and back on. LG says to wait 5 seconds before switching it back on, and Samsung notes that a tripped breaker can still look like it’s on.
- If your home uses a fuse box, a blown fuse is possible. Whirlpool and Maytag say to replace it if needed.
- Look at the power cord. If it is damaged, don’t use the washer.
LG USA Support has a video on a washer with no power:
If the outlet works, the breaker or GFCI stays set and the cord looks undamaged, check your brand’s no-power guidance before booking service. LG’s no-power guide adds a hard reset at this point: with the washer unplugged, hold the Power/Start button for 5 seconds, then hold the Play/Pause button for 5 seconds, plug it back in, power it on and start a cycle. If the display is still dark after the checks that apply to your brand, book service.
If a GFCI or breaker trips again, stop using the washer. If other devices fail on that outlet too, the outlet or circuit is the problem, and LG says to have an electrician fix an electrical fault.
Lights On but the Washer Won’t Start
If the panel is lit, the washer has power. Now check what is preventing the cycle from starting, in this order:
1. Control lock or child lock. If a lock icon or lock code is showing, unlock the controls before checking anything else.
| Brand | What you see | How to turn it off |
|---|---|---|
| Whirlpool, Maytag | LoC, LC or a lit Control Lock light | Press and hold the lock button for 3 seconds |
| LG | CL | With the washer on, hold the lock button, or both lock buttons, for 3 to 5 seconds |
| Samsung | A lit or flashing Child Lock icon | Press and hold the two Child Lock buttons |
LG says the lock stays on even when the washer is powered off, so unplugging won’t clear it. Button positions vary by model, so check your manual.
2. The door or lid. Close it firmly. On Whirlpool and Maytag front-loaders, the door can look closed without engaging the lock, and the lock can take about 10 seconds to engage after you press Start. On Whirlpool and Maytag top-loaders, the lid must be completely closed and latched. Some models fill without the lid latching, while others won’t start until it locks, so check your manual.
3. The water supply, on Whirlpool and Maytag front-loaders. Their no-start checks include the water. Make sure the hot and cold valves are fully open and both inlet hoses are connected. If the washer starts but no water enters, use our Washing Machine Not Filling With Water guide.
4. dr or Lid on the display. Some washers refuse to start after three cycles in a row without opening the door or lid. Whirlpool and Maytag front-loaders show dr, and GE electronic-control washers from 2017 on show Lid. Open and close the door or lid, then start again.
5. How you press Start. On Whirlpool and Maytag washers you may need to press and hold Start for up to 3 seconds. Some models show a countdown.
6. The cycle selection. On Whirlpool and Maytag front-loaders, -:-- means the cycle knob is on a position with no cycle. Turn it to a real cycle. Err appears if you changed the cycle while the washer was running or started it with the door open. Close the door and choose the cycle again.
7. A delay setting. If the display shows a delay time, check whether a Delay Start, Delay Wash or Delay End option is active, and follow your model’s instructions. On Whirlpool and Maytag front-loaders, a display of 1h to 12h means Delay Wash is on, and turning the power off cancels it.
8. Any other code. The same code can mean different things on different brands, so use the list in your manual.
The Panel Is On but the Buttons Don’t Respond
If no lock is active and the buttons still do not respond, try the restart your brand lists. Unplug the washer only if the floor is dry. If there is water near the plug, use the breaker.
- Samsung: moisture on the panel is normal in a humid room, so let it dry and try again. Some options don’t work with every cycle, so check your manual. If nothing changes, unplug the washer for 60 seconds, plug it back in and try again.
- LG: power off the washer, unplug it or turn off the breaker, then hold START/PAUSE for 5 seconds while it has no power. Restore power, turn the washer on and restart the cycle.
- Whirlpool and Maytag: unplug the washer or disconnect its power for 5 minutes, then plug it back in.
- GE: on electronic models from 2017 on,
CAnCELEdcan scroll after a cycle has been paused for more than 24 hours. The washer then ignores the controls for 4 minutes. Wait it out, because unplugging the washer restarts that 4-minute timer. To reset the electronic controls, GE says to turn off the breaker or unplug the washer for 2 minutes, then choose and start the cycle again.
Washing Machine Starts, Then Turns Off
If the washer runs normally at first and then stops, shuts off or goes dark partway through, use our Washing Machine Stops Mid Cycle guide. It covers what to check before you reset anything.
When to Stop and Book Service
Book service if any of these apply:
- The washer has no power after the outlet, GFCI and breaker checks, and the outlet works with another device.
- The power cord is damaged.
- A breaker or GFCI trips again after you reset it.
- It still won’t start after the lock, door or lid and restart checks above.
- A code returns after your brand’s restart steps.
Don’t open the cabinet or the control panel, and don’t test parts with a meter. If it still won’t start after the outside checks, an internal fault such as the door or lid lock or the controls becomes more likely and needs a technician. Tell the technician your model number, what the panel shows, any code, and which checks you have done.
For other washer problems, continue with our Washing Machine Troubleshooting guide.
Sources
- Whirlpool Product Help: No power, not turning on, front-load washer
- Whirlpool Product Help: Not starting or not operating, front-load washer
- Whirlpool Product Help: No power, top-load washer
- Whirlpool Product Help: Not starting, top-load washer
- Whirlpool Product Help: 1h, 2h, 3h up to 12h, front-load washer
- Maytag Product Help: Not starting or not operating, front-load washer
- Maytag Product Help: No power, top-load washer
- Maytag Product Help: Not starting, top-load washer
- Samsung US: Power issues with Samsung washing machine
- Samsung US: Samsung washing machine buttons won’t work
- LG USA: Why won’t my LG washing machine power on?
- LG USA: How to use the child lock feature
- LG USA: Troubleshooting unresponsive washer buttons
- GE Appliances: Washer, Consumer Help Indicator
- GE Appliances: Washer, resetting the electronic controls
Last reviewed: October 15, 2026