Washing Machine Not Filling With Water? Start at the Faucets

If your washing machine is not filling with water, open both faucets fully, straighten any kinked inlet hoses, and make sure hot is connected to hot and cold to cold. Then read the display. If there’s no code and still no water, clean the inlet screens as your manual directs. If it fills slowly, only fills with hot or cold, or starts and stops, use the matching section below. If these checks don’t restore water flow, book service.

Table of Contents

Is the Washer Actually Not Filling?

If the cycle has just started, or the clothes are getting wet, wait. The washer is working. These look like a no-fill but are normal:

  • Load sensing. Samsung washers weigh the load for 2–5 minutes before any water enters.
  • Delay or unlatched door. The washer won’t fill until the door or lid latches and any delayed start ends.
  • Suds pause. Some washers stop the cycle to deal with excess suds, then resume on their own.
  • Low water by design. HE washers use far less water than a standard top-loader. A shallow fill with wet laundry is normal.

If the door is latched, no delay is set, and the drum is still dry after the washer’s normal sensing period (up to 5 minutes on Samsung), treat it as a no-fill. Read the code next.

Read the Code for Your Brand

Find your brand. The same letters mean different things on another brand, so ignore code lists written for a different washer. For a true no-fill, use the No Water at All steps below. The table adds the checks that are specific to each brand.

BrandCodeWhat it meansDo this
Samsung4C, nF, 4ENot fillingDo the No Water steps and keep the faucets open while the washer runs. Also check that the drain hose is not kinked or pushed too far in (see Starts Filling, Then Stops). If the code stays, book service. Samsung’s full checklist is in Samsung Washer 4C Code.
SamsungnF1, 4C2, 4E2, CE, 14C2Hoses swappedSwap them: hot to hot, cold to cold. Samsung says reversed hose connections do not require service. Older models show nF or 4E for the same problem.
LGIE, E02, E10Tub did not fill in the set time (top-loaders show IE)Do the No Water steps. If the hoses are frozen, thaw them first (see Filling Slowly). If the code returns, book service.
Whirlpool front-loadF8 E1, Lo FLLow flow, or the washer can’t detect the incoming waterDo the No Water steps. If the door is locked and the controls don’t respond, the washer may be running an 8–10 minute drain routine. Wait 10 minutes. If the code stays, book service.
Whirlpool top-loadLF, Lo FL, F8 E1The fill took too longDo the No Water steps. Both hoses must carry water. If water enters and drains at the same time, see Starts Filling, Then Stops. If the code stays, book service.

Other brands: use the code list in your manual. The steps below apply to any washer.

Samsung example: This official Samsung video shows how to check a 4C or nF water-fill error. Codes and steps can vary by brand and model.

Washing Machine Not Filling With Water at All

If the washer is not filling with water at all, do these in order and stop when water enters:

  1. Open both faucets all the way and straighten both hoses.
  2. Connect the hot hose to the hot inlet and the cold hose to the cold inlet.
  3. If you’re using a Flood Safe or anti-flood device, connect the washer directly to the water supply as your manufacturer allows. Samsung says not to use Flood Safe hoses, and Whirlpool says anti-flood devices can restrict incoming water.
  4. Run another tap in the house. If it is weak or dry, the problem is the home’s water supply, not the washer.
  5. Samsung: after correcting the hose setup, unplug the washer for 1 minute, then plug it back in and restart the cycle.
  6. Clean the inlet screens as your manual directs. Turn off both faucets and unplug the washer before disconnecting the hoses, and keep a towel and a shallow pan under the connections. Don’t force a screen out if your manual does not show it as removable. An old toothbrush works for cleaning.
Checking a Washing Machine Inlet Screen
Hands checking the inlet screen and water hose connection on a washing machine

If water still doesn’t enter, stop and book service. Opening the cabinet to reach the inlet valve is not a home repair.

Only Hot or Only Cold Water

Check that the hot and cold hoses are on the correct inlets and that both faucets are open. If one side still doesn’t supply water, the fault is that supply line: clean its screen (step 6 above) and check its faucet and hose.

Before you blame the washer, rule out the normal causes:

  • A cycle may not call for both water supplies at the same time. Before treating one side as faulty, choose a cycle that should use the missing temperature.
  • Some Samsung settings labeled “Cold” still use the hot-water line when the incoming water is below 60°F. If only the cold line is connected, the washer can show a water-supply error.
  • No hot water at the other faucets either? The water heater is the problem. Samsung says to set it to at least 120°F and allow up to 30 minutes to recover.

Filling Slowly

For a slow fill, check the inlet screens, hoses, household water flow, and freezing before booking service.

  1. Clean the screens and straighten the hoses (steps 1 and 6 above).
  2. Run another tap. If it is slow too, the cause is your home’s water pressure.
  3. In freezing weather, LG says to wrap the faucet with a warm wet towel for 5 minutes. Disconnected inlet hoses can be thawed in warm water at 122°F or lower.

If it is still slow after all three, book service.

Starts Filling, Then Stops

  • It stops, then continues on its own: normal. See the first section.
  • Water seems to leave as fast as it enters: suspect siphoning from the drain setup. Check the hose depth and height against your manual, then use our Washing Machine Drain Clogged? Check These 3 Places guide for the drain-side setup.
  • A Whirlpool top-loader fills, then pumps out for about 8 minutes: one supply line has no water. Both hoses need water, or the lid locks and the washer drains. Fix the dry side using the hot and cold section above.
  • It stops and shows a code: use the table above.

If the Water Supply Is Fine but It Still Won’t Fill

If the water supply is good and the washer still won’t fill, stop there and book service. Give the technician your model number, the code on the display, and the checks you already completed.

If the washer keeps filling and the water does not stop, turn off the water supply and stop using the machine until it is checked.

For other washer problems, continue with our Washing Machine Troubleshooting guide.

Sources

Last reviewed: October 8, 2026