Run one drain cycle and watch the tub and the standpipe. If water stays in the tub or drains slowly, start on the washer side: check the drain hose and, if your model has one, the drain filter. If the tub empties but water rises or overflows from the standpipe (the pipe the drain hose empties into), a clog in the standpipe or household drain is more likely.
Table of Contents
Before you start
Unplug the washer before reaching behind it or opening a panel. Keep towels and a shallow tray close, because opening a filter or hose releases the water inside. After a hot cycle, Samsung recommends waiting about an hour.
This guide stops where plumbing starts. It doesn’t cover chemical drain cleaners or snaking a drain.
Step 1: Does the tub empty?
Run a drain or spin cycle and watch two places: the tub, and where the hose empties. That’s usually a standpipe in the wall, but it can also be a laundry tub or a floor drain. If water reaches the floor, stop the cycle.
If the water is coming from underneath the washer rather than from the standpipe or drain area, use our Washing Machine Leaking From Bottom? Check When It Happens guide instead.
| What you see | Where to check first |
|---|---|
| Tub stays full or drains slowly | The washer: Step 2 |
| Tub empties normally, but water rises or overflows where the hose empties | The standpipe: Step 3 |
| Tub empties normally, but a sink, tub, toilet or floor drain gurgles or backs up | The household drain: Step 4 |
Step 2: Check for a clog on the washer side
Hose first. Samsung calls a badly installed drain hose the most common cause of drain trouble, and says service is rarely needed. Look for kinks, bends or damage. The hose should be tied so it can’t slip down, shouldn’t seal airtight in the standpipe, and shouldn’t run through an extension kit.
| Hose inside the standpipe | Height | |
|---|---|---|
| Whirlpool (one model’s install guide) | 4.5 in. Don’t force extra hose in. Secure with a cable tie | Top of standpipe at least 39 in. from the floor, no higher than 96 in. from the bottom of the washer |
| Samsung (US support page) | Not less than 6 in. or more than 8 in. | At least 18 in. (24 in. for a wash basin), no higher than 96 in. (35 in. for a wash basin) |
| LG (US support page) | Check your manual | No higher than 96 in. above the bottom of the washer. Elbow bracket within 4 in. of the hose end |
These figures are manufacturer-specific, and even Samsung’s current US odor guidance uses different limits in different sections. Use your washer’s installation manual as the final reference.
On a Samsung, leave the screw that holds the hose against the back panel in place. If it’s missing, Samsung says the washer needs service.
Then the pump filter. Samsung and LG front-loaders have one you can remove. Samsung says top-loaders don’t. Whirlpool says it depends on the model, so check your manual. If you have one, put a container underneath, drain the small hose beside it first, then turn the filter counterclockwise. Pull out lint, coins and debris, rinse it, and turn it back in until it stops. LG suggests checking it whenever the washer drains slowly or shows an OE code.
Official LG video: Cleaning the drain pump filter on an LG front-load washer. Filter access varies by model.
Last, the floor. Samsung notes that a washer that isn’t level may not drain properly.
If the hose and filter are clear and the tub still holds water, use our Clothes Washer Won’t Drain guide to check the error code, load, cycle and detergent before booking service.
Step 3: Check the standpipe
The tub empties normally, so the question is whether the standpipe can keep up. In the Whirlpool installation guide used here, the standpipe is at least 2 inches in diameter and must handle 17 gallons per minute. Check your own model’s installation instructions before relying on those figures.
Next, check the standpipe height. The manufacturer figures in Step 2 start from the floor or the bottom of the washer. Plumbing codes start from the trap weir: the International Residential Code (section P2706.1.2) puts a standpipe at no less than 18 and no more than 42 inches above it. The two start from different points, so they can’t be compared directly. Follow your washer manual and the plumbing rules where you live; local codes can differ from the model code.
If the main problem is a rotten-egg or sewage smell rather than water backing up, see our guide to finding the source of a washing machine that smells like rotten eggs.
If the setup checks out and the standpipe still overflows, the blockage is in the standpipe, the trap under it, or the line beyond. You can’t see or safely reach that part, so it’s a job for a plumber.
Step 4: Check the household drain
If a sink, tub, toilet or floor drain gurgles or backs up while the washer drains, the washer is probably sharing the blocked line. Stop running the washer and call a plumber.
Who to call
| What’s happening | Call |
|---|---|
| Hose and filter are clear, tub still won’t empty | An appliance technician |
| Tub empties, but the standpipe overflows or other drains react | A plumber |
| Water at outlets or electrical connections, smoke, or a burning smell | Stop using the machine and get qualified help first |
For other washer problems, continue with our Washing Machine Troubleshooting guide.
Sources
- Samsung US: Samsung washing machine will not drain and Washing machine or laundry smells bad
- Whirlpool: Washer installation instructions, W11156977 and Cleaning the drain pump filter
- LG US: Top load washer: how to install the drain hose and How to clean the drain pump filter
- International Residential Code, section P2706.1.2
Last reviewed: October 11, 2026